![]() ![]() Since at least they could be more resilient in the event of interrupted data writes.Īn option would be to get software for the Mac that allows writing to NTFS, since I think that would be safer than ExFAT, but don't take my word for it. I am no expert on filesystems, but because HFS+ (and I think NTFS) are journaled, they would be inherently safer. But this pattern of having no problems with accidental disconnect of other drives, and 2 near death experience with the ExFat makes me wonder if the ExFat is somehow more vulnerable than other formats. Fortunately, running repair a second time worked (both times), and my drive is still ok. In fact both times the disk utility's first attempt to repair failed and the disk utility told me the drive was not repairable (which caused me much anxiety). In the few months that I have used this drive, I accidentally disconnected it 2 times and BOTH times, the next mount failed (unlike my prior WD drives which had no problems remounting) and I had to use Disk Utility to repair the disk. So this is the first drive i used ExFat for. I did this b/c i was considering the need to share this drive b/t both mac and windows environments. But I never had any problems other than the warnings.īut now i have been using a 2TB passport ultra that i formatted for ExFat. The next time I plugged it in, the drive would mount fine even though there might be a warning that prior disconnect was not proper. And while the computer would raise the warning "external device not ejected properly", i never had a problem. The devs make it clear that this opens up your Mac to potential exploitation, so this step is not for the faint of heart.I have been using many WD passports for years and years, with various capacities and various formats NTFS, FAT32 and MacOS Extended, and have occasionally disconnected them from a macbook without properly ejecting them (brain farts). There are some warnings about security on the project site you can check out the steps to enable it on the developer's GitHub page. You can boot your Mac into single-user mode and replace the built-in Mac NTFS tools with NTFS-3G. If you don't want to run these commands each time, there's a fix. Then: sudo /usr/local/bin/ntfs-3g /dev/disk1s1 /Volumes/NTFS -o local -o allow_other -o auto_xattr -o auto_cache Replace /dev/disk1s1 with the drive address that you found above: sudo mkdir /Volumes/NTFS You need to run the following commands each time that you want to mount a drive with write permissions. You can get this in the Terminal using the command: diskutil list You need to run a few extra commands to get it working.įirst, find the address of your mounted read-only drive. NTFS-3G enables your Mac to write to NTFS drives, but it is not automatic. ![]() How to Write to an NTFS Drive With NTFS-3G Once you've done that, try re-running the NTFS-3G command. You'll then be prompted to reboot your Mac. If that happens, run this command as well: Sometimes Terminal doesn't recognize that you have already installed the macFUSE package. That is another single command: brew install ntfs-3g Once you run the commands to install Homebrew, and you get a confirmation in Terminal, you need to install the NTFS-3G package. You'll need a couple of extra tools to complete the job, available in a Mac Homebrew package called NTFS-3G.įirst, install Homebrew by pasting this line into the Terminal: /bin/bash -c " $(curl -fsSL )" The program is a handler it doesn't contain anything to mount and read the files themselves. One of the most popular solutions is an open-source product: macFUSE for macOS.ĭownload macFUSE to get started. If you're in IT and deal with Windows drives regularly, you may need a better option. You'll see your drive listed here, and you can now copy files onto it.Įven if you're comfortable using Terminal, no one wants to edit a preference file every time they deal with a new drive. You can only get there in Finder click Go in the menu bar and select Go to Folder. Once it has remounted, it will be available in /Volumes. Hit Ctrl + O to save the file, then Ctrl + X to quit Nano. Then copy this line into the file, replacing DRIVENAME with the actual name of the drive you want to access: LABEL=DRIVENAME none ntfs rw,auto,nobrowse You need to follow these instructions for each drive you want to write to. But while macOS can read NTFS drives by default, its write capability hides behind a Terminal hack. Sometimes you may need to write some files to a locked drive only once, and you can do this with built-in Mac tools. We recommend you do not rely on this method for writing to important volumes or as a long-term solution. ![]() ![]() There is a very real chance that something could go wrong, resulting in a loss of data on the target drive. The following steps describe a method of enabling the experimental NTFS support in macOS. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |